Press the power button on the right of the device, you will then hear “Welcome to the Reli Light Cam Battery D1”.

Press and hold the power button for 10 seconds, you will then hear “The device is about to be shut down”.

Press and hold the power button for 3 seconds, you will hear “Reset Successfully”, then scan the QR code according to the app’s instructions.

Press and hold the power button for 3 seconds, you will hear “Reset Successfully”, then scan the QR code according to the app’s instructions.

1. The connection might be timed out, your camera might has exited the connection mode. Please exit the app page, reset the camera and try again.
2.Please make sure that the Wi-Fi signal in your area is strong, if the Wi-Fi signal is weak, or you are too far away from the router, the connection might fail. You can restart your router and try again.
3.Please check whether the Wi-Fi network works normally. You can try to use the mobile phone hotspot to configure the network for the camera. If the mobile phone hotspot can be connected, there might be something wrong with your Wi-Fi network. Please contact your network provider.

When the network environment changes, the camera needs to reconfigure the network. Please reset the camera and reconnect to the App.

There are two indicator lights at the bottom of the camera. The indicator light on the left is the network and status indicator. It is yellow when connecting to the network and it is blue in the working status; The indicator on the right is the charging indicator, which shows the state during charging. It is red during charging and green when fully charged.

Yes, go to devices page > click corresponding device > select camera settings > select light control and you will see the switch for the indicator lights. Please note, this may change due to app updates.

Please check whether your mobile phone has given the app recording permission.

Check whether the distance between the mobile phone and the device is too close during a call. The echo and noise generated during a close distance call are normal.

The app turns off the sound of the live screen by default. You can click the speaker icon to turn on the sound.

You need to install a memory card in your device. After installing a memory card, go to device page > click memory to watch all the recordings.

There is an SD card slot on the right side of the camera. Open the silicone pad and install the SD card into the device according to the prompt direction.

You may not have turned on the message notification switch. You can go to device settings page > Camera Settings > Notification settings > turn on push notifications. Please note, this may change due to app updates.

Go to the device page > click corresponding device > click share device, then follow the app’s instructions. Please note, this may change due to app updates.

Press and hold the button on the right side of the camera until you hear the voice prompt "Welcome to the Birddy Smart Bird House".

Press the power button, and your camera will indicate that it is shutting down.

Ensure the camera is charged. It's recommended to fully charge the camera before its first use.

Hold the button for 3 seconds until you hear "Reset Successfully," then follow the app's instructions to scan the QR code.

(1)5GHz networks are not supported. Use a 2.4GHz network or hotspot.
(2)Connection may time out; reset the camera and try again.
(3)Ensure strong Wi-Fi signal; consider restarting your router.
(4)If issues persist with Wi-Fi, test connection with a mobile phone hotspot and contact your network provider if necessary.

Network changes require camera reconfiguration. Reset the camera and reconnect to the App.

With 1-2 hours of sunlight per day, it can ensure continuous operation. Without birds, the device can stand by for up to five months.

One indicates network status and working status; the other shows charging status.

Yes, this option is available in the device settings within the app.

Install a memory card, then access the "Memory" option on the device page to view recordings.

Insert the SD card into the slot on the right side of the camera, as indicated.

Ensure the message notification switch is turned on in the device settings under Camera Settings > Notification settings.

From the device page, select the device and choose to share it, then follow the app's instructions.

Designed for small, omnivorous birds, with four different entrance sizes to accommodate various bird sizes.

The product is safe for the environment, humans, and animals, with passed radiation certifications.

Materials are certified and safe, using pine wood and non-toxic, odorless paint.

Yes, it features a small, reinforced entrance and a special stand design to prevent invasion by predators.

1. Connect the camera and the ground stand through the screw nut at the bottom of the camera.
2.Face the camera to the area you want to monitor.
3.Insert the stand into the ground.

1. Connect the camera and the strap mount through the screw nut at the back of the camera.
2.Wrap the strap mount around a branch.
3.Tighten the strap mount.

1. Connect the camera and the tripod bracket through the screw nut at the back or the bottom of the camera.
2.Secure the bracket.

1. Connect the camera and the desk and fence stand through the screw nut at the bottom of the camera.
2.Clip the clip to the edge of the table or fence.
3.The angle can be adjusted by bending the rod.

Hold the cleaning board with the groove facing outwards and slide it parallel into the Birddy Smart Bird House.

(1)Ensure the entrance's metal surface is facing outwards.
(2)Insert the metal rods into the slots at both ends of the entrance, horizontally. To secure, rotate 90 degrees until it’s fully locked in place.

(1)Feed the strap through the central opening of the Mounting Bracket. (2)Continue by threading it around a robust tree trunk and through the metal ring. Pull to tighten the strap, ensuring it is firmly secured.